\ OVERVIEW
PDMS manufacturing
Production-grade PDMS devices for organ-on-a-chip, organoids, cell culture, diagnostics and liquid biopsy. The material is the one you already use — Dow SYLGARD™ 184, with 182 where a slower cure is needed — so optical clarity, gas permeability and a direct plasma bond to glass are unchanged. What changes is the process: a closed replica mold, molding under calibrated pressure and batch bonding, run by trained technicians at up to 80,000 chips a month.


2 µm
minimum channel width

±5 µm
thickness tolerance, design-dependent

100+
cycles per closed replica mold — SU-8 wafer lasts 30–50

> 60 psi
bond strength, glass-to-PDMS and PDMS-to-PDMS

80,000
pieces per month capacity
\ CAPABILITIES
Capabilities and technical specifications
Geometry and features
Minimum channel width
≥ 2 µm
Channel depth tolerance
±5%
Channel aspect ratio
Up to 10:1
Minimum through-hole diameter
0.30 mm
Maximum chip size
Up to 300 × 300 mm
Layers and flatness
Layer count
2–8 layers
Alignment accuracy
0.10 mm typical; tighter on request
Thickness tolerance
Up to ±5 µm, design-dependent
Flatness
As low as 2 µm, held by closed-mold planarity control
Color
Clear as standard; tinted or colored PDMS on request
Laboratory PDMS vs. production PDMS
PARAMETER
LABORATORY PDMS
HICOMP PRODUCTION PDMS
Tooling
SU-8 on wafer, 30–50 cycles
Closed replica mold in a proprietary resin, 100+ cycles at 2 µm
Forming
Open cast — thickness set by gravity
Closed mold — thickness set by the tool, ±5 µm
Ports
Punched or drilled after cure
Molded in, or precision drilled with clean protocol
Bonding
One piece at a time, by hand
Batch bonding in fixtures, > 60 psi
Staffing
Trained scientists
Trained technicians
Output
Tens per week
Thousands per day, to 80,000/month

\ PROCESS
Manufacturing process
Six steps, two ways of doing them: the typical laboratory process and the closed-mold production line that replaces it.
-
Typical laboratory process Open tools, hand steps, outcomes measured afterwards.
Master mold
SU-8 photoresist on wafer; open tool; limited lifetime.
SU-8 wafer · 30–50 cycles
PDMS mixing
Manual weigh and hand-mix; variable degassing.
Operator-dependent ratio
Casting
Open cast on wafer; thickness and flatness set by gravity and surface tension, so they vary.
Thickness varies part to part
Bonding
Single-piece plasma bonding by hand.
One piece at a time
Ports and reservoirs
Manual punch or drill after cure; debris and misalignment risk.
Punched after cure
Assembly
Benchtop tubing; manual assembly.
Manual, undocumented
-
HiComp closed-mold production Every judgement call converted to a tool dimension or a machine setting.

Master mold
Mother-mold tooling by 3D printing, CNC, SU-8 and silicon etch; from it, a long-life closed replica mold in a proprietary resin for batch fabrication.
Closed replica mold · 100+ cycles at 2 µm

PDMS mixing
Metered mixing and controlled vacuum degassing in dedicated equipment — bubble-free bulk PDMS with batch-to-batch consistency.
Metered ratio · defined vacuum profile

Closed-mold molding
Closed-mold PDMS molding with calibrated pressure for thickness, planarity and surface-finish control. No free surface, so no meniscus.
±5 µm thickness · flatness to 2 µm

Bonding
Batch bonding in fixtures at high yield — bubble-free PDMS-to-PDMS and PDMS-to-glass, membranes and electrodes embedded in the stack.
> 60 psi · 2–8 layers

Ports and reservoirs
Molded-in ports and reservoirs — no punching step, so no punching defects — or precision drilling with capture and clean protocols.
Through-holes from Ø 0.30 mm

Assembly and packaging
Documented assembly of tubing, membranes and electrodes, or cartridge integration for high-volume packaging; 100% microscopic inspection; packed in the cleanroom.
Bare chip · tubing · cartridge
Which route suits your volume
The two tracks are not either-or. Below full production volume we run hybrid routes that borrow the closed-mold steps that lift yield most.
1–100 PCS PER ORDER
Prototype & small batch
Lab-style or hybrid, for speed.
100–500 PCS PER ORDER
Pilot / bridge
Hybrid, with selected closed-mold steps to lift yield.
≥ 500 PCS PER MONTH
High volume
Full closed-mold production for repeatability, cost and scale.
Every route
2–3 weeks
after design confirmation; expedites available
From quantity one
to 80,000 pieces a month; price improves with batch size
NRE from $1,500
covers the closed replica mold, DFM and first articles
100% microscopic inspection
ISO 7 cleanroom, ISO 13485 quality system
\ SHOWCASE
Sample parts and applications
\ TESTIMONIALS
“
Working with HiComp has allowed us to increase both the quality and the quantity of the organ-on-a-chip experiments that we conduct. Utilizing HiComp’s outstanding service and products has both made our lives easier and our research better.
John R. Minnick
NeuroAI and ML Researcher, University of California, Santa Cruz
FAQ




